Asus RT-AC1200G+ Page 101 User Manual Download

Page: 101 / 118

101

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating

in conjunction with any other antenna or transmitter.

CAUTION

: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

IMPORTANT

This device within the 5.15 ~ 5.25 GHz is restricted to

indoor operations to reduce any potential for harmful interference to

co-channel MSS operations.

against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Summary of Contents for RT-AC1200G+























































































































Search results

Summary of Contents for RT-AC1200G+

Reviews:

Related manuals for RT-AC1200G+

Brands by name

Popular brands

Asus RT-AC1200G+, User Manual

Search results

Summary of Contents for RT-AC1200G+

Reviews:

Related manuals for RT-AC1200G+

Brands by name

Popular brands