background image

5

800-810-WIRE (9473) • www.sargentlock.com • A7755A

Profile Series v.G1 Cylindrical Lock

 

Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. 

 

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibite

d.

3. Frame Preparation for Strike

Non Fire Rated Exterior Doors–  
Install Weather Conduit (P/N 52-2847)  
as shown below

4. Latchbolt and Fire Stop Plate Installation

1.  Install latch with beveled bolt facing the strike.
2.  Attach with two screws but DO NOT tighten completely at this time.
3.  Attach Fire Stop Plate with two screws.  

   

Note: Required for all Fire Rated doors

Centerline of 

latch front and 

strike

Screws (2) 

#8-32 x 3/4”

1-1/2"

(2) 1/8" Dia. holes x 1/4" Deep

required

7/8"

Through-bolt 

hole (2)

CL of 

1-1/2" Dia.

1-1/2"

(2) 1/8" Dia. holes 

required

7/8"

Fire 

stop plate

Through-bolt 

hole (2)

(2) Self tapping 

screws #8 x 1/2" 

long for wood 

& metal doors

Slot

CL of 

1-1/2" Dia.

Lockbody 

hole

Latchbolt 

door prep

Pre-drill

and/or tap

holes (2)

Inside

of door

Outside

of door

Hole for ribbon

cable from keypad  

to controller 

Lockbody 

hole

Latchbolt 

door prep

Pre-drilled

and/or tapped

holes 2 places

Inside

of door

Hole for ribbon

cable from keypad  

to controller 

 

Fire Rated Doors– Install Fire 
Stop Plate (P/N 52-0033)  
as shown below

IMPORTANT:

 Latch bevel must match door bevel and 

deadlocking latch must stop on strike when door is closed

Strike

A7755A.indd   5

11/9/18   12:05 PM

Summary of Contents for Sargent Profile G1 Series













Reviews: