Assa Abloy ADAMS RITE PS-SE Owner'S Manual And Installation Instructions Download Page 9

Page: 9 / 16

80-0180-339, Rev 2

2. REMOVE the orange jumper block installed into the BATT BACKUP

connector of the PS-SE circuit board by pulling the orange jumper
free from the circuit board.

NOTE:

Mounting points are available in the PS-SE enclosure for the

Battery Backup System circuit board.

3. INSTALL the Battery Backup System circuit board in the enclosure

(see Figure 4, “Location of Battery Backup System”).

Figure 4. Location of the Battery Backup System

NOTE:

The Adams Rite Battery Backup System circuit board has a

short wiring harness to connect to the PS-SE circuit board.

4. CONNECT the orange connector of the wiring harness into the BATT

BACKUP connector of the PS-SE circuit board.

5. WIRE the battery terminals of one battery to the (+) and (

–) terminals

on the BATT1 connector of the PS-SE circuit board.

6. WIRE the battery terminals of second battery to the (+) and (

–)

terminals on the BATT.21 connector of the PS-SE circuit board.

Summary of Contents for ADAMS RITE PS-SE

















Search results

Summary of Contents for ADAMS RITE PS-SE

Reviews:

Related manuals for ADAMS RITE PS-SE

Brands by name

Popular brands

Assa Abloy ADAMS RITE PS-SE, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for ADAMS RITE PS-SE

Reviews:

Related manuals for ADAMS RITE PS-SE

Brands by name

Popular brands