ASA Electronics 0200748A Original User Manual Download

Page: 56 / 66

DDM200 user manual - hardware

Created by: MPuchner 01.2020

version: 9600024A

Original user manual

page 56 of 66

printed: 25.02.2020

Figure 69

–

cabinet internals

•

Power supply unit for main drives

48VDC/20A

•

Power supply unit for device hub on ASA telescopes

24VDC/10A

•

Power supply unit for TCU

65W

•

IP-Remote power switch

Gude Expert Power Control 8211

The remote power switch provides 8 110/230VAC ports that can be switched on and off by using a web
interface. 3 ports are used for powering the main drives controller, ancillary drives controller and
telescope control unit (TCU).

The remaining available ports can be used for powering camera or other devices,
considering the technical specs of the device.

•

Ethernet Switch

8 port Gigabit switch
Connects devices such as mount and IP-remote power switch to your local network.

Use one of the available ports to connect the Ethernet switch inside the cabinet to your local network.

Use the AC cable to connect the cabinet to your 110/220VAC power socket (UPS).

Wall mounting brackets for the cabinet are included.

Summary of Contents for 0200748A



































































Search results

Summary of Contents for 0200748A

Reviews:

Related manuals for 0200748A

Brands by name

Popular brands

ASA Electronics 0200748A, Original User Manual

Search results

Summary of Contents for 0200748A

Reviews:

Related manuals for 0200748A

Brands by name

Popular brands