Arrow Cyclone 10 LP RefKit User Manual Download Page 12 | Manualshive

Page: 12 / 75

Arrow Cyclone 10 LP RefKit User Manual Download Page 12

Cyclone 10 LP RefKit User Guide

www.arrow.com

Page | 12

February 2022

Board Reference FPGA Pin No.

Pin Func.

Description

I/O Std

CLK12M

PIN_G21

Input

12MHz clock input

3.3 V

CLK_25M

PIN_AA12

Input

25MHz clock input

3.3 V

CLK_IN_SMA

PIN_B11

Input

Optional clock input

3.3 V

CLK_OUT_SMA

PIN_E5

Output

Optional clock output

3.3 V

3.3

Peripherals Connected to the FPGA

3.3.1

Communication and Configuration

The C10LP RefKit board uses a single chip to perform configuration of the device and
communication over USB.

3.3.1.1

JTAG Chain Configuration

There are two types of configuration methods supported by C10LP RefKit:

1.

JTAG Configuration:

configuration using JTAG ports. JTAG configuration scheme allows you to

directly configure the device core through JTAG pins (TDI, TDO, TMS and TCK pins). The
Quartus Prime software automatically generates a .sof that can be downloaded to the Cyclone
10 LP with a download cable through the Quartus Prime Programmer.

2.

Configuration from EPCQ-A flash:

configuration using external flash. Before configuration,

you need to program the configuration data .jic into the configuration flash memory (EPCQ-
A) which provides non-volatile storage for the bit stream. The information is retained within

scillat r

E

E

scillat r

CL I

CL

CL

E

CL

Figure 5

–

Cyclone 10 LP RefKit Clock Tree

«
...
10
11
12
13
14
...
»

Summary of Contents for Cyclone 10 LP RefKit












































































Reviews:

No comments