manualshive.com logo in svg

ARRI SkyPanel, User Manual

Share
Download
ARRI SkyPanel User Manual Download Page 46

Error Codes

46

Error Codes

Code

Error

Remedy

E.003

Controller over temperature.
STATUS LED lit up red.

Let the SkyPanel cool down. The STATUS indicator changes to green when the SkyPanel 
has cooled down. Turn the dimmer knob to „0“ or send an intensity value „0“ via DMX to 
activate the light engine again.

E.004

Light engine over temperature

See E.003

E.005

Missing LED supply.

The LED power supply is faulty. Please contact the ARRI service.

E.006

Calibration data of light engine 
faulty or EEPROM error.

WARNING: Loss of calibration data. This error can only be fixed by re-calibrating the light 
engine. Please contact the ARRI service.

E.007

Invalid PWM value calculation

Notice: The SkyPanel can be used on. This message is more a notification than an error.

E.008

Invalid values during calculation

See E.007

E.009

Invalid values during calculation

See E.007

E.010

Fan error. The fan speed devi-
ates or the fan doesn’t run at all.

Set the fan to LOW or High Speed and see if it starts rotating, in order to determine if there 
is an electrical malfunction. All mechanical tests or repairs may only be carried out by a 
trained service technician.

E.011

Fixture menu module not be 
detected.

If the fixture menu is working, error E.011 can be ignored. However, if the fixture menu 
remains dark (no LED lights up) we recommend to contact the ARRI service. They can 
then carry out detailed analyses.

E.012

Temperature sensor(s) are 
defective or deviation within 
NTC values too high.

One or more temperature sensors are defective or the deviation within the individual NTCs 
or BNTCs exceeds the variation tolerance of 12° C / 54° F. Check the error log (LSeries 
Manager) to see which temperature sensors are affected. Contact the ARRI service.

E.013

Calibration data faulty.

WARNING: Loss of calibration data. Fixture needs to be re-calibrated.

E.014

Watchdog error

Notice: The SkyPanel can be used on. This message is more a notification than an error.

E.015

LED channel faulty

Notice: The SkyPanel can be used on. This message is more a notification than an error.

Summary of Contents for SkyPanel









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands