ARM Cortex A9 Technical Reference Manual Download Page 32 | Manualshive

Page: 32 / 213

background image

Functional Description

ARM DDI 0388I

Copyright © 2008-2012 ARM. All rights reserved.

2-8

ID073015

Non-Confidential

Processor reset

A processor or

warm

reset initializes the majority of the Cortex-A9 processor, apart from its

debug logic. Breakpoints and watchpoints are retained during a processor reset. Processor reset
is typically used for resetting a system that has been operating for some time. Use

nCPURESET

and

nNEONRESET

for a warm reset.

MPE SIMD logic reset

This reset initializes all the SIMD logic of the MPE. It is expected to be applied when the SIMD
part of the MPE exits from powerdown state. This reset only applies to configurations where the
SIMD MPE logic is implemented in its own dedicated power domain, separated from the rest
of the processor logic.

ARM recommends the following reset sequence for an MPE SIMD reset:

1.

Apply

nNEONRESET

.

2.

Wait for at least nine

CLK

cycles. There is no harm in applying more clock cycles than

this, and maximum redundancy can be achieved by for example applying 15 cycles on
every clock domain.

3.

Assert

NEONCLKOFF

with a value of 1’b1.

4.

Wait for the equivalent of approximately 10 cycles, depending on your implementation.
This compensates for clock and reset tree latencies.

5.

Release

nNEONRESET

.

6.

Wait for the equivalent of another approximately 10 cycles, again to compensate for clock
and reset tree latencies.

7.

Deassert

NEONCLKOFF

. This ensures that all registers in the SIMD MPE part of the

processor see the same

CLK

edge on exit from the reset sequence.

Use

nNEONRESET

to control the SIMD part of the MPE logic independently of the

Cortex-A9 processor reset. Use this reset to hold the SIMD part of the MPE in a reset state so
that the power to the SIMD part of the MPE can be safely switched on or off. See

Debug reset

This reset initializes the debug logic in the Cortex-A9 uniprocessor, including breakpoints and
watchpoints values.

To perform a debug reset, you must assert the

nDBGRESET

signal LOW during a few

CLK

cycles.

2.3.3

Dynamic high level clock gating

The following sections describe dynamic high level clock gating:
•

•

Power Control Register

•

Dynamic high level clock gating activity

«
...
30
31
32
33
34
...
»

Summary of Contents for Cortex A9






















































































































































































































Reviews:

No comments

Related manuals for Cortex A9

Brand: Magnat Audio Pages: 2

Brand: Hama Pages: 4

grandMA2 Series

Brand: MA lighting Pages: 36

Brand: National Instruments Pages: 9

Brand: Lorex Pages: 186

Brand: NEC Pages: 2

Extreme Gaming VGA Cooler GV1000

Brand: ZALMAN Pages: 7

Brand: Infoblox Pages: 13

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Brand: Intel Pages: 112

Brand: Active Communications Pages: 10

Brand: Idis Pages: 18

Brand: TANDBERG Pages: 2

Brand: CopperOptics Pages: 12

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

FiberTwist XGS2420

Brand: Genexis Pages: 7

Brand: ACTi Pages: 12

Brand: MESA Electronic Pages: 27

Brand: H3C Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands