manualshive.com logo in svg

ARM ARM926EJ-S, Technical Reference Manual

The ARM ARM926EJ-S Technical Reference Manual is a comprehensive and invaluable resource for users seeking detailed information about this powerful processor. Download this manual for free from our website and gain access to all the technical specifications and capabilities of the ARM926EJ-S processor.

Share
Download
background image

Glossary 

ARM DDI0198D

Copyright © 2001-2003 ARM Limited. All rights reserved.

Glossary-7

CAM includes comparison logic with each bit of storage. A data value is broadcast to 
all words of storage and compared with the values there. Words that match are flagged 
in some way. Subsequent operations can then work on flagged words. It is possible to 
read the flagged words out one at a time or write to certain bit positions in all of them.

Context 

The environment that each process operates in for a multitasking operating system. In 
ARM processors, this is limited to mean the Physical Address range that it can access 
in memory and the associated memory access permissions.

See also 

Fast context switch.

Control bits 

The bottom eight bits of a Program Status Register (PSR). The control bits change when 
an exception arises and can be altered by software only when the processor is in a 
privileged mode.

Coprocessor 

A processor that supplements the main processor. It carries out additional functions that 
the main processor cannot perform. Usually used for floating-point math calculations, 
signal processing, or memory management.

Copy back

See 

Write-back.

Core 

A core is that part of a processor that contains the ALU, the datapath, the 
general-purpose registers, the Program Counter, and the instruction decode and control 
circuitry.

Core module 

In the context of an ARM Integrator, a core module is an add-on development board that 
contains an ARM processor and local memory. Core modules can run standalone, or can 
be stacked onto Integrator motherboards.

Core reset

See 

Warm reset.

CPI

See 

Cycles per instruction.

CPSR

See 

Current Program Status Register

CRF 

See

 Condensed Reference Format.

Current Program Status Register (CPSR) 

The register that holds the current operating processor status.

Cycles Per instruction (CPI) 

Cycles per instruction (or clocks per instruction) is a measure of the number of 
computer instructions that can be performed in one clock cycle. This figure of merit can 
be used to compare the performance of different CPUs against each other. The lower the 
value, the better the performance.

Summary of Contents for ARM926EJ-S

























































































































































































































































Reviews:

No comments

Related manuals for ARM926EJ-S

NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Intel Itanium 9010 Manual preview
Itanium 9010
Brand: Intel Pages: 108
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
IFM QHA200 Instructions For Setup preview
QHA200
Brand: IFM Pages: 12
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
Cypress Semiconductor CY7C1441AV33 Specification Sheet preview
CY7C1441AV33
Brand: Cypress Semiconductor Pages: 31
Hanwha Techwin Wisenet XRN-6410DB4 User Manual preview
Wisenet XRN-6410DB4
Brand: Hanwha Techwin Pages: 118
OWC ENVOY PRO MINI User Manual preview
ENVOY PRO MINI
Brand: OWC Pages: 7
Curtiss-Wright DTI-VME/S User Manual preview
DTI-VME/S
Brand: Curtiss-Wright Pages: 80
D-Link DSN-1100 Quick Start Manual preview
DSN-1100
Brand: D-Link Pages: 2
MSI TV@nywhere A/D Quick Installation Manual preview
TV@nywhere A/D
Brand: MSI Pages: 48

Brands by name

Popular brands

Load more brands