ARM ARM926EJ-S Technical Reference Manual Download Page 17

Page: 17 / 248

Preface

ARM DDI0198D

xvii

Chapter 6

Bus Interface Unit

Read this chapter for a description of the

Bus Interface Unit

(BIU)

interface to AMBA.

Chapter 7

Noncachable Instruction Fetches

Read this chapter for a description of how speculative noncachable
instruction fetches are used in the ARM926EJ-S processor to improve
performance.

Chapter 8

Coprocessor Interface

Read this chapter for a description of the coprocessor interface. The
chapter includes timing diagrams for coprocessor operations.

Chapter 9

Instruction Memory Barrier

Read this chapter for the

Instruction Memory Barrier

(IMB) description

and how IMB operations are used to ensure consistency between data and
instruction streams processed by the ARM926EJ-S processor.

Chapter 10

Embedded Trace Macrocell Support

Read this chapter to understand how

Embedded Trace Macrocell

(ETM)

is supported in the ARM926EJ-S processor.

Chapter 11

Debug Support

Read this chapter for a description of the debug interface and
EmbeddedICE-RT.

Chapter 12

Power Management

Read this chapter for a description of the power management facilities
provided by the ARM926EJ-S processor.

Appendix A

Signal Descriptions

This appendix lists the ARM926EJ-S processor signals in functional
groups.

Appendix B

CP15 Test and Debug Registers

Read this appendix for detailed information on the registers used for test
and debug.

Summary of Contents for ARM926EJ-S











































































































































































































































Search results

Summary of Contents for ARM926EJ-S

Reviews:

Related manuals for ARM926EJ-S

Brands by name

Popular brands

ARM ARM926EJ-S, Technical Reference Manual

Search results

Summary of Contents for ARM926EJ-S

Reviews:

Related manuals for ARM926EJ-S

Brands by name

Popular brands