manualshive.com logo in svg

ARM ARM926EJ-S, Technical Reference Manual

The ARM ARM926EJ-S Technical Reference Manual is a comprehensive and invaluable resource for users seeking detailed information about this powerful processor. Download this manual for free from our website and gain access to all the technical specifications and capabilities of the ARM926EJ-S processor.

Share
Download
background image

Programmer’s Model 

ARM DDI0198D

Copyright © 2001-2003 ARM Limited. All rights reserved.

2-29

7.

For each of the cache lines to be locked down in cache way 

i

: 

•

If a DCache is being locked down, use an LDR instruction to load a word 
from the memory cache line to ensure that the memory cache line is loaded 
into the cache. 

•

If an ICache is being locked down, use the register c7 MCR prefetch ICache 
line (CRm == c13, Opcode2 == 1) to fetch the memory cache line into the 
cache.

8.

Write to register c9, CRm == 0 setting L == 1 for bit 

i

 and restoring all the other 

bits to the values they had before the lockdown routine was started.

Cache unlock procedure

To unlock the locked down portion of the cache, write to register c9 setting L == 0 for 
the appropriate bit. For example, the following sequence sets the L bit to 0 for way 0 of 
the ICache, unlocking way 0: 

MRC p15, 0, <Rn>, c9, c0, 1;
BIC <Rn>, <Rn>, 0x01 ;
MCR p15, 0, <Rn>, c9, c0, 1;

TCM Region Register c9

The ARM926EJ-S processor supports physically-indexed, physically-tagged TCM. 
The TCM Region Register supports one region of instruction TCM and one region of 
data TCM. The minimum size of TCM region that can be supported is 4KB. The TCM 
Status Register indicates if TCM memories are attached (see 

TCM Status Register c0

 on 

page 2-12). The size of each TCM region is defined by the 

DRSIZE

 and 

IRSIZE

 input 

pins.

The data TCM is always disabled at reset. The instruction TCM is enabled at reset if the 

INITRAM

 pin is HIGH. This enables booting from the instruction TCM and sets the 

ITCM enable bit in the ITCM region register. You can use the TCM Region Register 
instructions listed in Table 2-22. 

Table 2-22 TCM Region Register instructions

Function

Data

Instruction

Read data TCM Region Register

Base address

MRC p15,0,<Rd>,c9,c1,0

Write data TCM Region Register

Base address

MCR p15,0,<Rd>,c9,c1,0

Read instruction TCM Region Register

Base address

MRC p15,0,<Rd>,c9,c1,1

Write instruction TCM Region Register

Base address

MCR p15,0,<Rd>,c9,c1,1

Summary of Contents for ARM926EJ-S

























































































































































































































































Reviews:

No comments

Related manuals for ARM926EJ-S

TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Nvidia nForce 680I LT SLI Hardware User Manual preview
nForce 680I LT SLI
Brand: Nvidia Pages: 80
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
Taiwan Commate Computer Inc. S630MA Quick Installation preview
S630MA
Brand: Taiwan Commate Computer Inc. Pages: 29
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Brand: Cromemco Pages: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Brand: Verizon Wireless Pages: 39
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
Idis DR-1204P Installation Manual preview
DR-1204P
Brand: Idis Pages: 22
Doremi MB-4K User Manual preview
MB-4K
Brand: Doremi Pages: 15
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
CompuLab CL-SOM-AM57 Series Reference Manual preview
CL-SOM-AM57 Series
Brand: CompuLab Pages: 79
Renesas M34502T-MCU User Manual preview
M34502T-MCU
Brand: Renesas Pages: 40

Brands by name

Popular brands

Load more brands