Ariens 926078 Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 34

background image

EN - 22

ADJUST TRACTION DRIVE

CLUTCH

1. Stop engine, remove key and wait for all

moving parts to stop and for hot parts to
cool.

2. Disconnect spark plug wire.
3. Loosen hardware securing belt cover to

unit and remove belt cover.

IMPORTANT:

DO NOT completely remove

hardware from unit.
4. Loosen jam nut on traction cable

adjustment barrel, and then turn
adjustment barrel down to shorten cable
and remove cable slack.

5. With the traction clutch disengaged,

make sure auger idler arm lightly touches
the frame. See Figure

6. Tighten jam nut on cable adjustment

barrel. See Figure

7. Reinstall belt cover and tighten hardware.
8. Reconnect spark plug wire.

Figure

37

1. Traction Drive Clutch Cable
2. Cable Adjustment Barrel
3. Jam Nut

Check position
here.

Figure

38

«
...
22
23
24
25
26
...
»

Summary of Contents for 926078



































Reviews:

No comments

Related manuals for 926078

Drive Pro EZ Build 41130

Brand: Meyer Pages: 11

Power X Change PXBLES-018

Brand: Ozito Pages: 10

Brand: Raider Pages: 96

Brand: Leister Pages: 4

Brand: Echo Pages: 30

Brand: EGO Pages: 76

Brand: Poulan Pro Pages: 44

Brand: Best Pages: 16

Minute Mount 2 XV2 Series

Brand: Fisher Pages: 16

Brand: Stanley Pages: 8

Brand: Troy-Bilt Pages: 20

Brand: Stanley Pages: 19

Brand: Boss Pages: 4

RT3 Undercarriage

Brand: Boss Pages: 4

Brand: WIFO Pages: 4

Brand: Honda Pages: 32

Brand: Honda Pages: 41

Brand: Honda Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands