Ariens 926078 Operator'S Manual Download Page 27

Page: 27 / 34

EN - 25

Unit does not
drive forward or
in reverse.

Traction drive cable is not
adjusted correctly.

Remove slack from cable. See

Adjust

Traction Drive Clutch

on page

22.

Traction belt is not functioning.

Repair or replace traction drive belt. Refer
to the service manual for your unit.

Speed selector is not adjusted
correctly.

Adjust speed selector. See

Transmission is bypassed.

Push the bypass rod in to engage the
transmission for normal operation. See

Move Unit Manually

on page

13.

Unit does not
throw snow or
throws it
poorly.

Shear bolts are broken.

See

Replace Shear Bolts

on page

18.

Attachment clutch / brake is not
adjusted correctly.

See

Adjust Attachment Clutch & Brake

page

19.

Impeller is frozen in place.

Move unit to a warm place to thaw.

Ice or debris is obstructing auger. Stop engine, remove key and wait for

moving parts to stop. Check for and
remove obstruction before restarting.

Discharge chute is clogged with
snow.

Stop engine, remove key and wait for all
moving parts to stop and for hot parts to
cool. Clean discharge chute and auger
housing with clean-out tool. DO NOT use
your hands.

Auger drive belt is slipping, worn
or damaged.

Adjust or replace auger drive belt. Refer
to the service manual for your unit.

Auger drive belt is loose or
damaged.

Replace belt or adjust auger control
cable. Refer to the service manual for
your unit.

Excessive
snow is left
behind.

Scraper blade is worn or
damaged.

Adjust when worn and replace when
damaged or when blade has been
adjusted down as far as possible and
does not touch ground or clear correctly.
See

Adjust Scraper Blade

on page

17.

Unit pulls to the
left or right.

Skid shoes and scraper blade
need adjustment.

Adjust skid shoes and scraper blade. See

on page 17.

Belt squeals
continuously.

Impeller may be frozen.

Move unit to a warm area to thaw.

Attachment clutch needs
adjustment.

See

Adjust Attachment Clutch & Brake

page

19.

TROUBLESHOOTING

Problem

Probable Cause

Correction

Summary of Contents for 926078



































Search results

Summary of Contents for 926078

Reviews:

Related manuals for 926078

Brands by name

Popular brands

Ariens 926078, Operator'S Manual

Search results

Summary of Contents for 926078

Reviews:

Related manuals for 926078

Brands by name

Popular brands