Argox AS-9500 User Manual Download Page 59

Page: 59 / 144

Code 93

Code 93 Message Length

Scan the bar codes below to change the message length. Minimum

and Maximum

lengths = 0-80. Minimum Default = 0, Maximum

Default = 80.

Code Page

Code pages define the mapping of character codes to characters. If

the data received does not display with the proper characters, it

may be because the barcode being scanned was created using a

code page that is different from the one the host program is

expecting. If this is the case, scan the bar code below, select the

code page with which the bar codes were created and scan the

value and the

Save

bar code from the Programming Chart on the

inside the back cover of this

manual. The data characters should

then appear properly.

*On

Minimum Message Length

Code 93 Code Page

Off

Maximum Message Length

Summary of Contents for AS-9500

















































































































































Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands

Argox AS-9500, User Manual

Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands