Argox AS-9500 User Manual Download

Page: 116 / 144

115

OCR Templates

You can create a custom “template,” or character string that

defines the length and content of OCR strings that will be read

with your imager. There are several choices when creating a

custom template for your application. You can create a template

for a single format, you can string together several formats, and

you can create a template for a user-defined variable. These

choices are described in detail below.

Creating an OCR Template

A single template allows you to program the imager to read any

combination of characters in the order you specify. Refer to

examples that follow the Template Characters table below.

Template Characters

Note:

OCR templates default to eight digits, no check character.

To Add an OCR Template

1. Turn on the OCR font you want to read .

2. Begin building the template.

Summary of Contents for AS-9500

















































































































































Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands

Argox AS-9500, User Manual

Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands