Argox AS-9500 User Manual Download Page 58

Page: 58 / 144

Interleaved 2 of 5

Check Digit

No Check Digit

indicates that the imager reads and transmits bar

code data with or without a check digit.

When Check Digit is set to

Validate, but Don’t Transmit

the unit only reads Interleaved 2 of 5 bar codes printed with

a check digit, but will not transmit the check digit with the

scanned data.

When Check Digit is set to

Validate and Transmit

, the imager

only reads Interleaved 2 of 5 bar codes printed with a check digit,

and will transmit this digit at the end of the scanned data.

Message Length

Scan the bar codes below to change the message length.

Minimum

and

Maximum lengths = 2-80. Minimum Default = 4, Maximum

Default = 80.

*On

*No Check Digit

Validate and Transmit

Maximum Message Length

Off

Validate , but Don’t Transmit

Minimum Message Length

Summary of Contents for AS-9500

















































































































































Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands

Argox AS-9500, User Manual

Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands