Argox AS-9500 User Manual Download Page 28

Page: 28 / 144

is the most sensitive setting, and 20 is the least sensitive. Default =

Hands Free Time-Out

The Auto-sense Modes is referred to as “hands free” modes. If the

hardware trigger is pulled when using a hands free mode, the

imager changes to manual trigger mode. You can set the time the

imager should remain in manual trigger mode by setting the Hands

Free Time-Out. Once the time-out value is reached, (if there have

been no further trigger pulls) the imager reverts to the original

hands free mode. Scan the

Hands Free Time-Out

bar code, then

scan the time-out duration (from 0-300,000 milliseconds) from the

inside back cover, and

Save

. Default = 5,000 ms.

Auto-sense

*LEDs On

LEDs Off

LED Time-Out

LED Time-Out Duration

Hands Free Time-Out

Sensitivity

Summary of Contents for AS-9500

















































































































































Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands

Argox AS-9500, User Manual

Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands