Argox AS-9500 User Manual Download Page 78

Page: 78 / 144

MSI

MSI Check Character

Different types of check characters are used with MSI bar codes.

You can program the imager to read MSI bar codes with Type 10

check characters.

When Check Character is set to

Validate and Transmit

, the

imager will only read MSI bar codes printed with the specified

type check character, and will transmit this character at the end of

the scanned data. When Check Character is set to

Validate, but

Don’t Transmit

, the unit will only read MSI bar codes printed

with the specified type check character, but will not transmit the

check character with the scanned data.

Message Length

Scan the bar codes below to change the message length. Minimum

and Maximum

lengths = 4-48. Minimum Default = 4, Maximum

Default = 48.

*Validate Type 10, but Don’t

Transmit

Minimum Message Length

*Off

Validate Type 10 and Transmit

Maximum Message Length

Summary of Contents for AS-9500

















































































































































Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands

Argox AS-9500, User Manual

Search results

Summary of Contents for AS-9500

Reviews:

Related manuals for AS-9500

Brands by name

Popular brands