Argo GREENSTYLE 12000 UE User Manual And Installation Manual Download Page 35

Page: 35 / 36

V 02/21

pipe.

tubo

pipe

limatrice

file

verso il basso

downwards

3. Secure an insulating tube

4. Install a union nut

• Remove the union nut on the

indoor connecting pipe and outdoor valve.

tall the union nut on the pipe.

9.52 (3/8")

1.6

1.0

6. Inspection

Check the quality of the expanded port.

If defective, expand

the port again following the procedure described above.

superficie liscia

smooth surface

allargamento imperfetto

defective expansion

lunghezza uguale

equal length

inclinato

slanted

superficie danneggiata

surface damaged

fessurazione

cracked

spessore irregolare

uneven thickness

tubo di raccordo

union pipe

tubo

pipe

REGULATION (EU) No. 517/2014 - F-GAS

The unit contains R32, a fluorinated greenhouse gas with global warming potential (GWP) = 675. Do not release R32

into the atmosphere.

Summary of Contents for GREENSTYLE 12000 UE





































Search results

Summary of Contents for GREENSTYLE 12000 UE

Reviews:

Related manuals for GREENSTYLE 12000 UE

Brands by name

Popular brands

Argo GREENSTYLE 12000 UE, User Manual And Installation Manual

Search results

Summary of Contents for GREENSTYLE 12000 UE

Reviews:

Related manuals for GREENSTYLE 12000 UE

Brands by name

Popular brands