background image

49

ARGO New Vehicle Limited Warranty

The warranty period is limited to 12 months from the date of retail sale, with the following exceptions:

Engine - 24 months from the date of retail sale separately by the engine manufacturer’s service network
Exide Battery -12 months free replacement from the date of retail sale by the battery manufacturer’s service network,

25 months total warranty, pro-rated

Tires - 3 months from the date of retail sale

Ontario Drive & Gear Limited hereby warrants to the original retail purchaser that each new and unused ARGO is free
from any defect in material or workmanship for the warranty period specified, under normal use and service by the
original purchaser.

This warranty is void unless a Warranty Registration Form 670-11 and Pre-Service Checklist Form 670-11 have both
been properly completed and returned to Ontario Drive & Gear Limited within 10 days of the date of retail sale.

This warranty is not transferable unless an application of transfer has been approved by Ontario Drive & Gear Limited
and a new warranty card has been issued.

This warranty shall not apply to used or demonstrator ARGOs or to such units delivered to a distributor or dealer more
than 12 months before its retail sale, unless a warranty validation is obtained from Ontario Drive & Gear Limited by
written notice specifying the vehicle in question.

This warranty is void immediately upon the ARGO being used in any speed contest (racing, dragging, etc.).

This warranty does not cover the following items:

1. Machines or parts lost or damaged during shipment.

2. Normal maintenance or adjustments after initial pre-servicing is completed.

3. Normal replacement of service items.

4. Accessory items not supplied by Ontario Drive & Gear Limited.

5. Damages resulting from:

-

misuse, accident, theft or fire

-

use of improper or insufficient fuel, fluids or lubricants

-

use of parts other than genuine ARGO replacement parts

-

modifications, alteration, tampering or improper repair performed by parties other than an authorised

ARGO dealer or distributor

-

any device or accessories installed by parties other than an authorised ARGO dealer or distributor

6. Batteries that fail due to improper charging or installation; broken container, cover or terminal sulphation or

dehydration; damage caused by fire, excessive heat, wreckage, explosion, freezing, the addition of any chemical or
solution other than the battery grade sulphuric acid.

This shall constitute the complete and only warranty given by Ontario Drive & Gear Limited, and, except as specifi-
cally set forth in the foregoing, Ontario Drive & Gear Limited shall not, in any event, be liable for any losses, damages
or costs, whether special, incidental, consequential or otherwise, in any way related to any vehicle or its sale.  No
warranty, expressed, implied or statutory, as to merchantability, fitness for a particular purpose, description, quality or
any other matter is given in connection with any

ARGO vehicle or its sale and no agent, employee or other per-

son has any authority to vary any of the foregoing provisions.  Provided, however, that this clause shall be severable
where voided by application of the Consumer Protection Act.

Summary of Contents for 6x6 Bigfoot





























































Reviews: