46
SECTION 10
ACCESSORY INFORMATION
WARNING
CAUTION
CAUTION
WARNING
Do not step on or place loads on the edge of the body over the
trailer wheels. This area of the trailer body is intended only
as a mud guard.
Follow the instructions listed in Section 6.4.5 of this manual
to service the axle bearings. Do not allow water and debris
to accumulate in the bottom of trailer body to avoid prema-
ture bearing failure.
Keep fingers clear of tongue swiveling components.
10.20 Heater Kit - Conquest (Part No. 848-10)
The heater kit includes a conventional automotive style hot
coolant heater core with 2 speed fan to circulate the warm air
through the ducts to the right side of the driver’s compart-
ment and the windshield. In some operating conditions, ie.
high humidity or full passenger load, defrosting the
windshield and side panel windows may not be effective.
When the heater is not required, the heater valve should be
closed, diverting all of the coolant through the engine radia-
tor.
In extremely cold weather and operating at low load, the
heater may perform like a second radiator and keep the en-
gine from reaching proper operating temperature. Under these
conditions, a piece of cardboard or similar material should
be used to partially cover the engine radiator.
The 850-40 Alternator is essential to provide the electrical
power to operate the heater fan and maintain the battery
charge rate.
10.21 ROLL OVER PROTECTION STRUCTURES
(Part Nos. 848-40-2 & 848-40-4)
Roll Over Protection Structures (ROPS) are designed for use
on all Argo 8 x 8 models. Part No. 848-40-2 provides roll
over protection and lap belts for the driver and front seat
passenger. Part No. 848-40-4 provides roll over protection
and lap belts for driver, front seat passenger and two passen-
gers in the optional rear bench seat (Part No. 849-60).
The ROPS design provides reasonable protection from in-
jury in the event of a rollover. DO NOT rely on it to protect
the occupants from irresponsible driving.
The ROPS has been designed to meet the requirements of
the Occupational Health and Safety Act - Regulation 856
‘Roll-Over Protection Structures’ for the Province of Ontario,
Canada.
Seat belts must be properly adjusted and worn by all oc-
cupants at all times EXCEPT when operating in water.
Never carry more people in the vehicle than there are
seat belts for.
Articles must not be placed on top of the ROPS.
Use caution when traveling on uneven ground; the ROPS
reduces vehicle stability.
No part of the ROPS shall be drilled, welded or altered in
any way without the manufacturer’s authorization.
Do not exceed maximum gross vehicle weight of 907 kg
(2000 lbs.)
Use caution when traveling tree-lined trails. Branches
could be knocked down, causing injury to the vehicle oc-
cupants.
FAILURE TO COMPLY WITH THE ABOVE COULD
RESULT IN PERSONAL INJURY OR DEATH.
DO NOT use the ROPS as an attachment point for tow-
ing or winching the Argo.
Check fastener tightness annually. Inspect for and re-
place any damaged or worn parts of the ROPS and the
seat belts.
10.22 REAR BENCH SEAT (Part No. 849-60)
This bench seat assembly is similar to the front bench seat
design, providing a back rest and more comfort for two per-
sons riding in the rear compartment of any current Argo 8 x
8 model. The seat cushion and back rest are easily removed
to use the rear compartment for cargo.
Always ensure that the spring loaded pull pin (Part No.
849-72) on each side is fully engaged after installing the
seat. Pull the seat hard to ensure that it is secured prop-
erly.
Never attach a tow line to the handrail of the seat back
rest.
When a roll over protection structure (ROPS) is installed,
seat belts must be installed for rear bench seat passen-
gers and used properly.
