Arctiko LTF 225 Operating Instructions Manual Download Page 4

4

Operating Instructions

1.

The freezer should be connected by an authorised electrician, or by the company which sold
the freezer! Incorrect installation may damage the freezer.

2. 

Place the freezer on a flat floor which can take the weight of the freezer.

3. 

The electrical installation should be earthed.

4. 

Do not use extension cables, but connect the freezer directly to a fixed installation. If the freezer is 

connected to a long extension cable there is the risk that the cable will become hot.

5. 

The freezer should be placed in a dry location, and should not be subjected to water on the cabinet. 

If water gets into the electrical parts it may cause short-circuiting.

6. 

In the event of functional or electrical irregularities, please contact an authorised servicing engineer.

7. 

Do not put bottles containing carbonic acid or inflammable products in the freezer.

Disposal and scrapping of the freezer: Remove the lock, so that there is no risk of children getting locked in 
the freezer whilst playing.

Electrical Connection

The machine meets current EU directives. Low voltage 

2006/95/E.E.C.

Electromagnetic compatibility 

2004/108/E.E.C.

The machine should be given extra protection in accordance with the Electricity Supply Regulations in order 
to protect the user against dangerous electric shocks in the event of faults.

If the switch is for a three-pin plug, a three-pin plug should be used, and the conductor with yellow/green 
insulation should be connected to the Earth terminal.

The Cooling System

The vaporiser is built into the wall of the inner container. This will be - 65°C, so there is a risk of frost-bite if it 
is touched. Always use thermal gloves when touching the contents of the freezer.

The condenser is placed on the inside of the cabinet. This means that the outside of the cabinet gets hot 
when in operation. The advantage of a hot cabinet is that it will always be dry.

The advantage of freezing boxes is that only a minimum amount of heat gets in when they are opened and 
closed.

Thermostat with digital display. Once the freezer is cooled down, the set temperature and the temperature 
shown will be the same.

Summary of Contents for LTF 225





















Reviews: