Arcteq AQ-F213 Instruction Manual Download Page 94

Page: 94 / 455

Table. 5.3.1 - 48. Setting parameters for reset time characteristics.

Name

Range

Step

Defa

fault

ult Descrip

Description

tion

Delayed

pick-up

release

0: No

1: Yes

Resetting characteristics selection (either time-delayed or instant) after

the pick-up element is released. If activated, the START signal is reset

after a set release time delay.

Release

time delay

0.000…150.000s 0.005s 0.06s

Resetting time. The time allowed between pick-ups if the pick-up has not

led into a trip operation.

If the "Delayed pick-up release" setting is active, the START signal is held

on for the duration of the timer.

Op.Time

calculation

reset after

release

time

0: No

1: Yes

Operating timer resetting characteristics selection. When active, the

operating time counter is reset after a set release time if the pick-up

element is not activated during this time. When disabled, the operating

time counter is reset directly after the pick-up element is reset.

Continue

time

calculation

during

release

time

0: No

1: Yes

0: No

Time calculation characteristics selection. If activated, the operating time

counter continues until a set release time even if the pick-up element is

reset.

The behavior of the stages with different release time configurations are presented in the figures below.

Figure. 5.3.1 - 82. No delayed pick-up release.

Q-F213

-F213

Instruction manual

Version: 2.04

Summary of Contents for AQ-F213







































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands

Arcteq AQ-F213, Instruction Manual

Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands