Arcteq AQ-F213 Instruction Manual Download Page 402

Page: 402 / 455

5. Scan

Scans Slot D and finds the five channels of the CT module (fixed for AQ-X213). If the CTM is

not found, the device issues an alarm.

6. Scan

Scans Slot E, and moves to the next slot if Slot E is empty. If the scan finds an 8DI module, it

reserves the designations "DI7", "DI8", "DI9", "DI10", "DI11", "DI12", "DI13" and "DI14" to this

slot. If Slot C also has an 8DI module (and therefore has already reserved these

designations), the device reserves the designations "DI15", "DI16", "DI17", "DI18", "DI19",

"DI20", "DI21" and "DI22" to this slot. If the scan finds a 5DO module, it reserves the

designations "OUT6", "OUT7", "OUT8", "OUT9" and "OUT10" to this slot. Again, if Slot C also

has a 5DO and has therefore already reserved these designations, the device reserves the

designations "OUT11", "OUT12", "OUT13", "OUT14" and "OUT15" to this slot. If the scan finds

an arc protection module, it reserves the sensor channels ("S1", "S2", "S3", "S4"), the high-

speed outputs ("HSO1", "HSO2") and the digital input channel ("ArcBI") to this slot.

7. Scan

A similar operation to Scan 6 (checks which designations have been reserved by modules in

previous slots and numbers the new ones accordingly).

Thus far this document has only explained the installation of I/O add-on cards to the option module

slots. This is because all other module types are treated in a same way. For example, when an

additional communication port is installed into the upper port of the communication module, its

designation is Communication port 3 or higher, as Communication ports 1 and 2 already exist in the

CPU module (which is scanned, and thus designated, first). After a communication port is detected, it

is added into the device's communication space and its corresponding settings are enabled.

The fully optioned example case of AQ-X213-XXXXXXX-BBC

BBC (the first image pair, on the right) has a

total of 22 digital input channels available: two (DI1…DI2) in the CPU module, four (DI3…DI6) in the

voltage measurement module, and the rest in Slots C and E in groups of eight. It also has a total of 10

digital output channels available: five (DO1…DO5) in the CPU module, and five (DO6…DO10) in Slot

F. These same principles apply to all non-standard configurations in the AQ-X213 IED family.

Q-F213

-F213

Instruction manual

Version: 2.04

401

Summary of Contents for AQ-F213







































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands

Arcteq AQ-F213, Instruction Manual

Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands