Arcteq AQ-F213 Instruction Manual Download Page 55

Page: 55 / 455

VREC

Measurement value recorder

Table. 5.1 - 7. Communication protocols of AQ-F213.

FFunction packa

unction package

Name

NTP

Modbus/TCP

Modbus/RTU

Modbus I/O

IEC 61850

GOOSE

IEC 103

DNP3

IEC 101/104

SPA

5.2 Measurements

5.2.1 Current measurement and scaling

The current measurement module (CT module, or CTM) is used for measuring the currents from

current transformers. The measured values are processed into the measurement database and they

are used by measurement and protection functions. It is essential to understand the concept of current

measurements to be able to get correct measurements.

Q-F213

-F213

Instruction manual

Version: 2.04

Summary of Contents for AQ-F213







































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands

Arcteq AQ-F213, Instruction Manual

Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands