Arcteq AQ-F213 Instruction Manual Download Page 331

Page: 331 / 455

Name

Range

Step

Default

Description

Curve1...4 output

-1 000

000.00...1 000

000.00

0.00001 -

Displays the output of the curve.

The input signal filter (see the image below) calculates the average of received signals according to the

set time constant. This is why rapid changes and disturbances (such as fast spikes) are smothered.

The Nyquist rate states that the filter time constant must be at least double the period time of the

disturbance process signal. For example, the value for the filter time constant is 2 seconds for a 1

second period time of a disturbance oscillation.

When the curve signal is out of range, it activates the "ASC1...4 input out of range" signal, which can

be used inside logic or with other relay functions. The signal can be assigned directly to an output relay

or to an LED in the I/O matrix. The "Out of range" signal is activated, when the measured signal falls

below the set input minimum limit, or when it exceeds the input maximum limit. The "Out of range"

signal is very useful when e.g. a 4…20 mA input signal is used (see the image below).

If for some reason the input signal is lost, the value is fixed to the last actual measured cycle value. The

value does not go down to the minimum if it has been something else at the time of the signal breaking.

Table. 5.4.10 - 219. Output settings and indications.

Name

Range

Step Default

Description

Curve 1...4

update cycle

5...10

000ms

5ms

150ms

Defines the length of the input measurement update cycle. If the user wants

a fast operation, this setting should be fairly low.

Q-F213

-F213

Instruction manual

Version: 2.04

330

Summary of Contents for AQ-F213







































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands

Arcteq AQ-F213, Instruction Manual

Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands