Arcteq AQ-F213 Instruction Manual Download Page 166

Page: 166 / 455

Table. 5.3.10 - 102. Pick-up settings.

Name

Range

Step Default

Description

Pick-up

terms

0: 1 voltage

1: 2 voltages

2: 3 voltages

0: 1

voltage

Selects the pick-up criterion.

set

50.00…150.00

0.01

105 %U

The pick-up setting.

Delay type 0: DT

1: IDMT

0: DT

Selects the delay type time counter. The selection possibilities are

dependent (IDMT, Inverse Definite Minimum Time) and independent (DT,

Definite Time) characteristics.

Time dial

setting k

0.01...60.00

0.01

The time dial/multiplier setting for IDMT characteristics. This setting is

only visible when "IDMT" is the selected delay type.

Definite

operating

time delay

0.000...1800.000

0.005

0.04 s

The definite time operating delay. This setting is active and visible when

"DT" is the selected delay type.

When set to 0.000 s, the stage operates as instant without added delay.

When the parameter is set to 0.005...1800 s, the stage operates as

independent delayed.

IDMT

multiplier

0.01...25.00

0.01

1.00

The IDMT time multiplier in the U

set

power. This setting is only visible

when "IDMT" is the selected delay type.

Release

time delay

0.000...150.000

0.005

0.06 s

Determines the time allowed between pick-ups if the pick-up has not led

into a trip operation. During this time the START signal is held on for the

timers if the delayed pick-up release is active.

Delayed

pick-up

release

0: Yes

1: No

0: Yes

Selects the resetting characteristics. Either time-delayed or instant after

the pick-up element is released. If activated the START signal is reset

after a set release time delay.

Op.Time

calc reset

after

release

time

0: Yes

1: No

0: Yes

Selects the operating timer resetting characteristics. When actived, the

operating time counter is reset after a set release time if the pick-up

element is not activated during this time. When disabled, the operating

time counter is reset directly after the pick-up element reset.

Continue

time

calculation

during

release

time

0: Yes

1: No

Selects the time calculation characteristics. If activated, the operating

time counter continues until a set release time even if the pick-up

element is reset.

The pick-up activation of the function is not directly equal to the START signal generation of the

function. The START signal is allowed if the blocking condition is not active.

Read-only parameters

The relay's

Info page displays useful, real-time information on the state of the protection function. It is

accessed either through the relay's HMI display, or through the setting tool software when it is

connected to the relay and its Live Edit mode is active.

Table. 5.3.10 - 103. Information displayed by the function.

Name

Range

Step

Description

U< pick-

up setting

0.0...1 000 000.0 V

0.1 V

The primary voltage required for tripping. The displayed pick-up voltage

level depends on the pick-up setting and the voltage transformer

settings.

Expected

operating

time

0.000...1800.000 s

0.005 s

Displays the expected operating time when a fault occurs. When IDMT

mode is used, the expected operating time depends on the measured

voltage value. If the measured voltage changes during a fault, the

expected operating time changes accordingly.

Q-F213

-F213

Instruction manual

Version: 2.04

165

Summary of Contents for AQ-F213







































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands

Arcteq AQ-F213, Instruction Manual

Search results

Summary of Contents for AQ-F213

Reviews:

Brands by name

Popular brands