Aquaavia SWIMSPA, User And Installation Manual

Page: 14 / 34

User’s and installation manual SWIMSPA – FITNESS POOL English
41902E 15 EN-V00
“Warm” / “Cool” Temperature adjustment
Press either pad once, and the LCD will display
the temperature which has been set.
Each time either of these pads is pressed
again, the set temperature will increase or
decrease in steps of 0,5ºC. After three
seconds, the LCD will automatically display the
current spa temperature.
“ Jets 1 ”
Press this pad to operate pump 1. Press again
to stop the pump. If left running, the pump
will turn off after 30 minutes.
“
Jets 2 ”
Press this pad to operate pump 2. Press again
to stop the pump. If left running, the pump
will turn off after 30 minutes.
“ Blower ” Air pump
(Only in deluxe version)
On the Spa section of the Fitness Pool this
button will start the air boost motor if
installed. As above the motor will
automatically stop after 30 minutes.
“ Light ”
This pad turns the pool light on and off. It left
on, it will automatically turn off after 4 hours.
“ Mode/Prog ” (“ Standard ”, “ Economy ” or
“ Sleep ”)
Press this pad to switch between modes. Press
“
Mode/Prog ” to start to program; press “ Cool ”
to define the operation mode. Press
“
Mode/Prog ” to confirm the selection.
Standard mode maintains the set temperature
at all times. Economy mode heats the water
only during filter cycles. Sleep mode sets back
the temperature by 10°C and runs as in
Economy. See the Filter Cycle Programming
section for more filter/heater options.
The
“Mode/Prog” button is used to switch
between Economy, Standard or Sleep operation
modes and also serves as an “
Enter ” button to
initiate various programming features.
Stand-by mode
If you press “
Warm ” or “ Cool” and after “ Jets
2 ” all the functions of the spa will be annulled
temporarily and there will appear on screen
the word "SbY" . This is useful when you have
to change the filter. Pressing any other button
the spa will return to the normal operation.
“
Time ”
This button is to set the time and is used for
programming some other functions (see
Initial
start-up section). Press the “ Time ” button to
view the time of day. To change the time of
day, see “Time of Day” in the “Initial Start-up”
section of this Owner’s Manual.
Text display inverted
Press “ Warm ” or “ Cool ” and after “ Blower ” to
see the text inverted. To return to the normal
operation press the same sequence again.
Leds colour light (Optional)
If your Swimspa has a colour leds light, press
the button
"Light" of the main panel to turn
on and off the light. To change the sequence
of colours, press the push-button
"D" .
If after starting the light you switch off, the
next time you start your light, it will remain in
the colour of the previous time you used the
light.
On the other way, if you leave the light on, it
will be turned off automatically after 4 hours
and the next time you press
"Light" you will
have to wait 2 minutes without touching any
button until the light will be on automatically.
Locking the control pad
To lock the entire control pad, press “ Time ”
button then the “ Jets 1 ” button then the
“ Warm ” button all within 3 seconds.
When locked, the display will show “PL” and
the spa temperature. All buttons will be frozen
less “
Time ”.
Unlocking the control pad
By pressing the “ Time ” button then the “ Jets 1 ”
button then the “ Cool ” the lock symbol will
disappear and the control pad buttons will
work again.
Locking the temperature only
To lock the temperature, press either the
“Warm” or “Cool” button to initiate the “set
heat” mode. Next, and within a 3 second time
span, press “
Time ” button then the “ Jets 1 ”
button then the “ Warm ” button. When locked,