Aqua Lung Legend LX Second Stage Technical Maintenance Manual Download Page 12

Page: 12 / 18

12 Legend First Stage Service Manual

Table 1 - Troubleshooting Guide

SYMPTOM

POSSIBLE CAUSE

TREATMENT

Leakage or freeflow from second stage

1. High first-stage intermediate pres-

sure. (should be 135±5 psi)

1. Refer to first-stage Troubleshoot-

ing Guide.

2. LP seat (26) damaged or worn.

2. Replace LP seat.

3. Crown (21) adjusted incorrectly, lever

set too high

3. Reset crown preliminary set-

tings, and repeat Adjustment

Procedures.

4. Lever (25) bent

4. Replace lever.

5. Crown (21) sealing surface dam-

aged.

5. Replace crown.

6. Poppet spring (11) damaged.

6. Replace spring.

Low purge or excessive work of breath-
ing (full cylinder)

1. Low first-stage intermediate pres-

sure. (should be 135±5 psi)

1. Refer to first-stage Troubleshoot-

ing Guide.

2. Crown (21) adjusted incorrectly, lever

set too low.

2. Reset crown to preliminary

settings and repeat Adjustment

Procedures

3. Intermediate pressure hose (40)

clogged or obstructed.

3. Clean or replace hose.

4. Lever (25) bent

4. Replace lever.

Water entering second-stage

1. Hole in mouthpiece (12).

1. Replace mouthpiece.

2. Demand diaphragm (7) damaged.

2. Replace diaphragm.

3. Exhaust valve (13) damaged.

3. Replace valve.

4. Venturi lever o-ring (16) dirty, dam-

aged, or worn.

4. Disassemble and replace o-ring.

5. Diaphragm improperly seated be-

tween box bottom (29) and sealing

ring (5).

5. Remove front cover (3) and

properly reassemble sealing

ring with diaphragm (check for

distortion).

6. Box bottom damaged. (Check ex-

haust valve sealing surface.)

6. Disassemble and replace box

bottom

7. Inlet o-ring (17) damaged.

7. Replace o-ring.

8. Valve spindle o-ring (20) worn or

damaged

8. Replace o-ring.

Summary of Contents for Legend LX Second Stage


















Search results

Summary of Contents for Legend LX Second Stage

Reviews:

Related manuals for Legend LX Second Stage

Brands by name

Popular brands

Aqua Lung Legend LX Second Stage, Technical Maintenance Manual

Search results

Summary of Contents for Legend LX Second Stage

Reviews:

Related manuals for Legend LX Second Stage

Brands by name

Popular brands