Aqua Lung Legend LX Second Stage Technical Maintenance Manual Download Page 14

Page: 14 / 18

14 Legend First Stage Service Manual

Table 3 - Recommended Lubricants & Cleaners

LUBRICANT / CLEANER

APPLICATION

SOURCE

Christo-Lube

MCG-111

All O-rings seals

Aqua Lung, PN 820466, or

Lubrication Technologies

310 Morton Street

Jackson, OH 45640

(800) 477-8704

Oakite #31

Acid bath for reusable stainless

steel and brass parts.

Oakite Products, Inc.

50 Valley Road

Berkeley Heights, NJ 07922

White distilled vinegar (100 gr.)

Acid bath for reusable stainless

steel and brass parts.

"Household" grade

Liquid dishwashing detergent

(diluted with warm water)

Degreaser for brass and stainless

steel parts; general cleaning solu-

tion for plastic and rubber

"Household" grade

CAUTION:

DO NOT use muriatic acid for the cleaning of any parts. Muriatic

acid, even when strongly diluted, can harm chrome plating, and may leave a
residue that is harmful to O-ring seals and other parts.

CAUTION:

Silicone rubber requires no lubrication or preservative treatment. DO NOT

apply grease or spray to silicone rubber parts. Doing so may cause a chemical break-
down and premature deterioration of the material.

Summary of Contents for Legend LX Second Stage


















Search results

Summary of Contents for Legend LX Second Stage

Reviews:

Brands by name

Popular brands

Aqua Lung Legend LX Second Stage, Technical Maintenance Manual

Search results

Summary of Contents for Legend LX Second Stage

Reviews:

Brands by name

Popular brands