background image

Updated 6/16/2016 

 

Copyright Apeks LLC, 2014 

25 

4.1.21.  Disconnect the two blue water line quick connects on the back of the collection cup.   
4.1.22.  Attach the collector cup quick connects together and attach the bottom separator 1 

quick connect to the heat exchanger quick connect.  This will ensure water flow even 
if collector cup connections are not re-attached in assembly.  

4.1.22.1.  Caution if removing the cup in the middle of a run with the pump on this step 

must be followed or the system will automatically shut down due to lack of water 
flow.  

4.1.23.  Use caution to support and not to drop the collector cup, remove the high pressure 

sanitary clamps from the bottom of the separator 1 with 5/8-in ratchet wrench. 

4.1.24.  Remove the collection cup from Separator #1. 
4.1.25.  Collect the oil from inside the collection cup. 

4.1.25.1.  Note: there is typically residual dry ice in the collection cup mixed in with the oil.  

The dry ice will sublimate without any additional heat.  It is sometimes more 
efficient to remove the dry ice/oil mixture and place it in collection device (like a 
Pyrex dish). 
 

 

 

Figure 26.  Image of collection cup after removal from separator. 

 

4.1.26.  Use the round squeegee and alcohol to thoroughly clean the inside of the separator 

and collection cup. 

4.1.27.  Separator #1 and the collection cup must be cleaned after each extraction. 
4.1.28.  Reassemble separator #1 by reversing the steps above, excluding the connection 

piping from separator #1 to #2. 

4.1.29.  When reassembling, check gaskets for integrity and grove seals for cleanliness. 
4.1.30.  Prior to reassembling separator #1 cap, check orifice for clog and orientation. 
4.1.31.  Reconnect the collector cup water lines with quick connect to original configuration 

before turning on the chiller/heater. 

Summary of Contents for 2000 PSI Series

























































Reviews: