background image

 17 

 

CARE and MAINTENANCE 

 
Soldering Iron Error Messages 

1.  Soldering  Iron  connection  assembly  is  not  connected  or  not  properly 

connected to the receptacle on the control panel. 

2.  Soldering iron tip is damaged and needs to be replaced. The device will  

display “PLUG”.  

3.  Indicating a problem with the contacts of the soldering iron 

or the tip. 

 
 

This  appliance  can  be  used  by  children  aged  from  8  years  and  above  and  persons  with  reduced 
physical,  sensory  or  mental  capabilities  or  lack  of  experience  and  knowledge  if  they  have  been 
given supervision or instruction concerning use of the appliance in a safe way and understand the 
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall 
not be made by children without supervision. 
 
The  specific  instructions  related  to  the  safe  operation  of  this  appliance  (as  given  in  7.12  of  this 
standard) shall be collated together in the front section of the user instructions. 
The height of the characters, measured on the capital letters, shall be at least 3 mm. 
These instructions shall also available in an alternative format, e.g. on a website. 

 

A fire may result if the appliance is not used with care, therefore: 

 

be careful when using the appliance in places where there are combustible materials ; 

 

do not apply to the same place for a long time; 

 

do not use in presence of an explosive atmosphere; 

 

be aware that heat may be conducted to combustible materials that are out of sight; 

 

place the appliance on its stand after use and allow it to cool down before                                             
storage; 

 

do not leave the appliance unattended when it is switched on. 

 

Rohs  

Correct Disposal of this product 

This marking indicates that this product should not be disposed with 
other household wastes throughout the EU. To prevent possible harm 
to the environment or human health from uncontrolled waste dis-
posal, recycle it responsibly to promote the sustainable reuse of 
material resources. To return your used device, please use the return 
and collection systems or contact the retailer where the product was 
purchased. They can take this product for environmental safe recy-
cling. 

 

 

Summary of Contents for INT866





















Reviews: