AnyCubic i3 MEGA Quick Start Manual Download Page 3

Page: 3 / 43

Safety Instructions

Please carefully read the safety instructions before get started.

ANY

CUBIC

3D printer generates high temperature. Do not reach inside of the

printer during operation. Allow time for the printer to cool down after printing.
Contact with extruded materials may cause burns. Wait for printed objects to cool
before removing them from the build platform.

ANY

CUBIC

3D printer includes moving parts that can cause injury.

Vapors or fumes may be irritating at operating temperature. Always use the

ANY

CUBIC

3D printer in an open, well ventilated area.

Be cautious when using the scraper. Never direct the scraper towards your hand.

ANY

CUBIC

3D printer MUST NOT be exposed to water or rain.

ANY

CUBIC

3D printer is designed to be used within ambient temperature ranging

8ºC-40ºC, and humidity ranging 20%-50%. Working outside those limits may
result in low quality printing.

It is recommended to use protection glasses when cleaning/sanding the printed
models to avoid small particles contacting eyes.

In case of emergency, immediately turn off the

ANY

CUBIC

3D printer and contact

us or consult for professional advice.

Never leave the

ANY

CUBIC

3D printer unattended during operation.。

Summary of Contents for i3 MEGA












































Search results

Summary of Contents for i3 MEGA

Reviews:

Related manuals for i3 MEGA

Brands by name

Popular brands

AnyCubic i3 MEGA, Quick Start Manual

Search results

Summary of Contents for i3 MEGA

Reviews:

Related manuals for i3 MEGA

Brands by name

Popular brands