ANTAIRA APN-210N User Manual Download Page 52

Page: 52 / 70

Enable Read-Only Account

Read-Only

Username

Password:

new password used for read-only administrator authentication should be

specified.

Configuration Management

Backup Configuration:

click Download button to export the current configuration to a file.

Upload Configuration:

click Browse button to navigate to and select the new

configuration file or specify the full path to the configuration file location.

Activating the Upload button will transfer new configuration file to the system.

New configuration will be effective after the Apply button is activated and system reboot

cycle is completed. Previous system configuration is deleted after Apply button is

activated. It is highly recommended to backup the system configuration before uploading

the new configuration.

Use only configuration backups of the same type device - configuration backed up from

PowerStation2 suits only PowerStation2, but not LiteStation2 or LiteStation5! Behavior

may be unpredictable when mixing configurations from different type devices.

Device Maintenance

The controls in this section are dedicated for the device maintenance routines: rebooting,

resetting, generating of the support information report.

Reboot:

activate Reboot control in order to initiate full reboot cycle of the device. Reboot

effect is the same as the hardware reboot which is similar to the power off - power on

cycle. The system configuration is not modified after the reboot cycle completes. Any

non-applied changes will be lost.

Reset to Defaults:

activate Reset to Defaults control in order to initiate reset the device

Summary of Contents for APN-210N







































































Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands

ANTAIRA APN-210N, User Manual

Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands