ANTAIRA APN-210N User Manual Download Page 54 | Manualshive

Page: 54 / 70

background image

54

Status Page

The Status Page displays a summary of link status information, current values of basic

configuration settings (depending on operating mode), network settings and traffic

statistics of all the interfaces.

Status Reporting

Main

Uptime:

displays device up time since boot up. The time is expressed in days, hours,

minutes and seconds.

Host Name:

displays the assigned device host name (ID).

System Time:

display device current date and time. Accurate system date and time is

retrieved from the internet services using NTP (Network Time Protocol) if device is setup

and connected to internet. Otherwise, the date and time update from device own

inaccurate autonomous clock.

Version Firmware Version:

displays current firmware version in operation.

Loader Version:

displays current loader version of the device.

«
...
52
53
54
55
56
...
»

Summary of Contents for APN-210N







































































Reviews:

No comments

Related manuals for APN-210N

Brand: Ocens Pages: 2

Brand: Icom Pages: 2

Brand: Tenda Pages: 57

EWP-WA6630X-JP-FIT

Brand: H3C Pages: 34

Brand: versa Pages: 103

Brand: E-Lins Pages: 52

RailBox 11ac/WiFi 5

Brand: Acksys Pages: 36

Brand: Ebyte Pages: 27

Brand: Loopcomm Pages: 2

Brand: Linksys Pages: 64

Brand: Linksys Pages: 30

Juplink RX4-1500

Brand: Vanin Pages: 2

Brand: HomeMatic Pages: 67

Brand: EnGenius Pages: 80

Brand: HPE Pages: 4

Brand: Gigafast Pages: 54

Brand: VTel Wireless Pages: 12

Brand: VTEL Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands