ANTAIRA APN-210N User Manual Download Page 50

Page: 50 / 70

System Tab

The System Page contains Administrative options. This page enables administrator to

customize, reboot the device, set it to factory defaults, upload a new firmware, backup or

update the configuration and configure administrator’s credentials.

Firmware Upgrade

Use this section to find out current software version and update the device with the new

firmware. The device firmware update is compatible with all configuration settings. System

configurations are preserved while the device is updated with a new firmware version.

Firmware version:

displays the version of the current firmware of the device system.

Upgrade:

button opens the Firmware Upload window if activated.

Current Firmware:

displays the version of the device firmware which is currently

operating.

Firmware File:

activate Browse button to navigate to and select the new firmware file.

The full path to the new firmware file location can be specified there. New firmware file is

transferred to the system after Upload button is activated.

Close this window

– button cancels the new firmware upload process if activated.

Upgrade button

should be activated in order to proceed with firmware upgrade routine

(new firmware image should be uploaded into the system first). Please be patient, as the

firmware upgrade routine can take 3-7 minutes. The based device will be un-accessible

until the firmware upgrade routine is completed.

Do not switch off, do not reboot and do not disconnect the device from
the power supply during the firmware upgrade process as these actions
will damage the device!

It is highly recommended to backup the system configuration and the Support Info file

before uploading the new configuration.

Close this window

– button closes the firmware upgrade window if activated.

This action will not cancel the firmware upgrade process.

Summary of Contents for APN-210N







































































Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands

ANTAIRA APN-210N, User Manual

Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands