ANTAIRA APN-210N User Manual Download Page 5

Page: 5 / 70

Table of Contents

Overview ......................................................................................................... 7

Introduction .................................................................................................... 7

Features and Benefits

.................................................................................................... 8

Hardware Installation ..................................................................................... 9

DIN-Rail Installation ....................................................................................... 9

Wall Mount Installation

................................................................................................. 10

Hardware Overview ...................................................................................... 11

Front Panel

.................................................................................................................... 11

Front Panel LEDs

......................................................................................................... 12

Top Panel

....................................................................................................................... 12

Rear Panel

..................................................................................................................... 13

Cables and Antennas ................................................................................... 14

Ethernet Cables

............................................................................................................ 14

10BaseT/100BaseTX Pin Assignments

.................................................................... 14

Wireless Antenna

.......................................................................................................... 15

Operation Modes & Connection Examples ................................................ 16

Access Point and Access Point WDS Mode

............................................................ 16

Access Point WDS Mode

............................................................................................ 16

Station Mode

................................................................................................................. 17

Station WDS Mode

....................................................................................................... 18

Repeater WDS Mode

................................................................................................... 19

Configure the IP Address ............................................................................ 19

For Windows 95/98/98SE/ME/NT

.............................................................................. 20

For Windows XP/2000

................................................................................................. 21

Access the Web Interface............................................................................ 23

Access with uConfig

..................................................................................................... 23

Access with Web Browser

........................................................................................... 26

Navigation .................................................................................................... 29

Main Menu Bar

.............................................................................................................. 29

How to save changes

.................................................................................................. 29

Basic Network Tab ....................................................................................... 30

Network Mode: Bridging

.............................................................................................. 30

LAN Setup

..................................................................................................................... 30

Basic Wireless Tab ...................................................................................... 33

Basic Wireless Settings

............................................................................................... 33

Wireless Mode

.............................................................................................................. 33

Access Point Parameters Settings

............................................................................ 34

Station Parameters Settings

....................................................................................... 36

Wireless Security

.......................................................................................................... 38

Virtual Access Point (VAP)

.......................................................................................... 43

Summary of Contents for APN-210N







































































Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands

ANTAIRA APN-210N, User Manual

Search results

Summary of Contents for APN-210N

Reviews:

Related manuals for APN-210N

Brands by name

Popular brands