ANTAIRA AMS-2111 Series User Manual Download Page 2

Page: 2 / 17

Industrial Wireless Access Point
Hardware User's Manual

– AMS-2111

This document contains information which is protected by copyright. Reproduction, adaptation, or translation without prior

permission is prohibited, except as allowed under the copyright laws.

Trademark Information

Antaira is a registered trademark of Antaira Technologies, LLC., Microsoft Windows and the Windows logo are the trademarks

of Microsoft Corp. All other brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

Antaira Technologies, LLC. provides this manual without warranty of any kind, expressed or implied, including but not limited

to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies, LLC. may make

improvements and/or changes to the product and/or specifications of the product described in this manual, without prior notice.

Antaira Technologies, LLC. will not be liable for any technical inaccuracies or typographical errors found in this guide.

Changes are periodically made to the information contained herein and will be incorporated into later versions of the manual.

The information contained is subject to change without prior notice.

Summary of Contents for AMS-2111 Series

















