background image

15

7.Control menu

The control panel situated on the top cover of the ArcPixel Power-CE allows fixture addressing and set the 

driver´s behaviour.

Control elements:

 

[ENTER] button- enters menu,confirms adjusted values and leaves menu. 

 ,    [UP] button and[DOWN] button- moves between menu items on the the same level, sets values.

  [ESCAPE] button- leaves  the menu without saving value.  

7.1 DMX Addr (

Fixture addressing

)

Set DMX Address 

- use this menu item to set the DMX start address of the fixture, which is defined as the first 

channel from which the ArcPixel Power-CE will respond to the DMX controller.

 

IP address - 

select this menu item to set desired IP address. IP address is the Internet protocol

 

address.The IP uniquely identifies any node (fixture) on a network. There cannot be 2 fixtures with

 

the same IP address on the network!

  

Default Address. 

This address is derived from fixture´s MAC address and 

 

 

cannot be changed. Confirm the item 

"Set Address" 

to select this address.

  

Custom Address. 

IP address consists of four decimal numbers, each ranging

 

 

from 0 to 255, separated by dots, e.g., 172.16.254.1. Each part represents a group of 8 bits

 

 

(octet) of the address.

 

 

The following items 

"IP Adr 1"

" IP Adr 2", " IP Adr 3", " IP Adr 4"

 allow to set each 

 

 

part (number) of the address. After setting desired IP address, confirm the item

  

"Set Address" 

to save this address.

Network mask -

 select this menu item to set desired network mask. A network mask is a 32-bit mask used to 

divide an IP address into subnets and specify the networks available hosts. 

The following items 

"Net M.1"

"Net.M.2", " Net.M.3", " Net.M.4"

 serve for seting of each part (number) of 

the net mask. 

After setting desired network mask, confirm the item 

"Set Net M." 

to save adjusted values.

7.2 Info (

Fixture information

)

Use this menu to read useful information about the fixture.

Software version 

- select this menu item to read software versions.

  

Dot 10.0/20

 

-

 

Dot version. 

The items show software version of each LED module.

  

MA. In

 

-

 

Driver version. 

The item shows software version of the ArcPixel Pover-CE.

IP Addr

 

 

- this menu item shows the current IP address.

MAC Addr

 - select this menu item to read the MAC address (the MAC address "runs" on display).

Dots

 - select this menu item to read information about connected LED modules (ArcDot, ArcPix)

  New Dots

 - the item shows the number of recently connected LED modules.

  

Unknown Dots

 - t

he item shows the number of LED modules which were not d

etected

  

 by the dot checking procedure ("Search Dots") or are new dots after replacement.

Summary of Contents for ArcPixel Power CE



























Reviews: