Analytik Jena qTOWER3 84 Operating Manual Download Page 17 | Manualshive

Page: 17 / 46

background image

Safety instructions

qTOWER

3

84 / qTOWER

3

84 G

Edition 02.19

15

2.8

Standards and directives

Safety class and safety type

The qTOWER³ 84 features protection class

I

.

The casing features protection type IP 20.

Device safety

The qTOWER³ 84 complies with the safety standards



EN 61010-1:2010



UL 61010-1:2012



CAN/CSA-C22.2 No. 61010-1-12:2012

EMC compatibility

The qTOWER³ 84 has been tested for radio interference suppression and interference
resistance and meets the requirements of



EN 61326-1:2013 Interference resistance



EN 61326-1:2013

Interference emission

The qTOWER³ 84 complies with the applicable requirements of EMC directive
2014/30/EU and low voltage directive 2014/35/EU.

Environmental compatibility

The qTOWER³ 84 has been tested for environmental compatibility and meets the re-
quirements of



DIN EN 60068-2-1, Ab, 2008-01



DIN EN 60068-2-2, Bb, 2008-01



DIN EN 60068-2-78, Cab, 2014-02



DIN EN 60068-2-6, Fc, 2008-10



DIN EN 60068-2-64, Fh, 2009-04



DIN EN 60068-2-27, Ea, 2010-02



DIN EN 22248



DIN EN 22206

«
...
15
16
17
18
19
...
»

Summary of Contents for qTOWER3 84















































Reviews:

No comments

Related manuals for qTOWER3 84

Brand: UnionSpecial Pages: 56

Brand: Omnia Pages: 8

Brand: Tascam Pages: 27

Brand: Jay-Lor Pages: 72

Brand: MacDon Pages: 198

Brand: M-Triangel Pages: 6

Brand: ICP DAS USA Pages: 45

SC 2 Deluxe EasyFix

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 16

Brand: Nabtesco Pages: 26

Brand: TC Electronic Pages: 67

Brand: Tascam Pages: 3

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

VIMCO Sivoia SV-CCI-GRP

Brand: Lutron Electronics Pages: 2

Retractable Box Scrapers HR3584

Brand: Land Pride Pages: 1

EPL-HB-150LED-RT-IBSC

Brand: Larson Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands