background image

UG-169 

Evaluation Board User Guide

 

Rev. 0 | Page 2 of 12 

TABLE OF CONTENTS 

Features .............................................................................................. 1

 

General Description ......................................................................... 1

 

Digital Picture of Evaluation Board ............................................... 1

 

Revision History ............................................................................... 2

 

Evaluation Board Hardware ............................................................ 3

 

Setting Up Jumper Connections................................................. 3

 

Setting Up the Power and PC Connections .............................. 3

 

Setting Up the Signal Connections ............................................ 3

 

Bypassing the 6 V Wall Socket Power Supply........................... 3

 

Using I

2

C Serial Port Mode ......................................................... 4

 

Evaluation Board Software Setup ................................................... 5

 

Installing the Software ................................................................. 5

 

Using the Software ........................................................................5

 

Software Operation ...........................................................................6

 

Menu Bar of Main Window .........................................................7

 

Using the Software to Control the Functional Blocks of 
AD9523...........................................................................................8

 

PLL 1 Controls...............................................................................8

 

PLL 2 Controls...............................................................................9

 

Channel Divider Window ......................................................... 10

 

Output Driver Window ............................................................. 10

 

EEPROM Control ...................................................................... 11

 

Quick Start Guide to the AD9523 ................................................ 12

 

 

REVISION HISTORY 

7/10—Revision 0: Initial Version 

 

           

Summary of Contents for AD9523













Reviews: