manualshive.com logo in svg

AMX TDS, Operation/Reference Manual

Share
Download
AMX TDS Operation/Reference Manual Download Page 87

Serial Commands

79

AMX TDS (Television Delivery System) 

Serial Commands

Overview

Direct user interface to both the Transmitter and the Receiver is done via the RS232 serial connection. All 
commands available via UDP are available via serial.



Each tuner broadcasts and receives on the same IP, with the port set to 

5000

 on the main PCB tuner 

and 

5001

 on the daughter board tuner.



Commands via UDP to the RX unit use port 

2008.



The default baud rate is 

115200

.

Entering Command Mode

In order to configure the network settings via the CONSOLE Port, the Receiver must be placed in Command 
mode. 

DTV-RX02-HD High-Definition Receivers

To place the DTV-RX02-HD Receiver in Command mode, press ’Enter’ while the unit is booting up. To 
reboot, re-cycle power to the unit by disconnecting and re-connecting the 12VDC POWER connector on the 
rear panel.

DTV-RX01-SD Receivers

To place the DTV-RX01-SD Receiver in Command mode, send the following 

IPTVsetup

 serial command:

IPTVsetup<LF><CR>

ClearQAM/ATSC (High Definition) Serial Commands

The following serial commands are supported by both DTV-TX03-US Transmitters and DTV-RX02-HD 
Receivers: 

ClearQAM/ATSC (High Definition) Serial Commands

boot

Exit boot loader prompt and start booting firmware

setip

Display current IP setting in bootloader to be passed to kernel when booting up.

Note: This command does not display current network setting in firmware. It is only used to check 
what has been configured before booting up the unit.

setip lan

Following prompts to configure LAN network settings. This setting takes effect immediately after 
the unit boots up.

Enter DHCP option (0/1) >

Enter ipAddr:

Enter subnet:

Enter Gateway:

Enter priDNS:

Enter secDNS:

Enter DomainName:

Note: If DHCP is set, all other options to enter IP address setting will be skipped. If entry is not 
valid, it will be prompted again. If second entry is still not valid, the configuration will exit without 
saving.

Note: All DTV Transmitters and Receivers must have an assigned IP Address, Network Mask, 
and Gateway Address in order for the DTV system to work correctly. This applies to units that uti-
lize DHCP and to units that have been assigned Static IP addresses. If you are using DHCP, verify 
that these address assignments are provided by the DHCP Server.

Summary of Contents for TDS











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands