background image

Avoid exposing the 601ES Explosive Safety

DMM to extremes of temperature which will

affect accuracy and shorten battery pack
lifespan.

Once the 601ES DMM main power switch is
turned "ON" and following a (1) minute

warmup, (

) the AMPTEC 601ES

Explosive Safety DMM should be ready for

general purpose testing and use.

The 601ES DMM operator may be asked to

perform a series of tests (i.e. verify the test
current is less than 10mA with the unit's DC

milliammeter) prior to connection to any
explosive device under test.

Test lead sets may also be placed in the pouch
which holds the laminated AMPTEC 601ES

DMM Operator Instruction Card.

provided there is No ‘LO BAT’

Indicator shown

To replace low batteries first unscrew the

battery compartment lid and lift. Remove the

battery holder, plastic tie and low batteries.
Replace with a new set of (4) “AA” batteries

according to polarity. Using the spare plastic tie

included in the battery compartment, wrap the
plastic around the battery holder and secure.

Cut excess plastic. Next, wrap the black and
red wire around the battery holder and place the

holder into the compartment. Lastly replace lid

and screw in screws to secure. See Fig. A-4
above. *Please note: After replacing battery

holder with (4) new ‘AA’ batteries; secure with

a new plastic tie lock.

The 601ES Explosive Safety DMM consumes

little power and generates virtually no heat.
Consequently, it may be used in any area where

the environment does not exceed the

specifications of Table B-1.

A-5. Setup and Use

BATTERY HOLDER

‘AA’ BATTERY

FIG. A-4

Sect. A - Receiving and Initial Inspection

The AMPTEC 601ES DMM comes factory set with
an “Auto Turn-Off” time out of 30 minutes.

With certain batteries at the end of their power
capacity the “LO BAT” display may be only on for a
minute or less before the 601ES Automatically shuts
down. As an example, if you turn it on and don't see

“LO BAT”. Then in a few minutes walk out on and
return to discover the meter is turned off,

are the primary reason for this. Any time

the “LO BAT” display stays on for more than a

second or two it is time to exchange the batteries.

low

batteries

6

Summary of Contents for 601ES






















Reviews: