Ametek 5100 HD, User Manual

Page: 116 / 134

6-16 | Model 5100 HD Analyzer
40
111
30 “Cell pres Hi” Warning 254, 495, 496 Cell pressure (254) is outside of a band
set by min/max pressure (495, 496)
111 31
“Cell pres Low”
Warning
111 32 "Span error" Warning Error in span calibration
112 1 "Zero error" Warning Error in zero calibration
113 2 "User error" Warning User error detected from the user analog
input
Common Modbus Registers
ID Access Data
Type
mnemonic MB
Starting
Regs
MB Reg
Size
Description
6 rs char[20] SERIAL 0 10 Serial Number
7 rs char[6] MAC 10 3 MAC address
8 rws uint IP 13 2 IP Address
9 rws uint SUBNET 15 2 IP Subnet Mask
10
rws uint GW 17 2 Gateway
11
rws uint DNS 19 2 DNS
12
rws uint16 DHCPE 21 1 DHCP enable. 1=disabled, 2=enabled
13
rws uint16 TCPE 22 1 TCP Enable. 0=disabled, 1=enabled
14
rws uint SVRIP 23 2 Server IP
100 rwf int16 CFGFILEVER 25 1 Version of the params.xml file generated by
this
101
r char[20] VERSION 26 10 Software Version
102 r char[20] NAME 36 10 Model Name
103 rw uint IU1BAUD 46 2 Internal UART1baud rate (MODBUS)
104 rwf uint IU2BAUD 48 2 Internal UART2 baud rate (DISPLAY)
105 rwf uint EU1BAUD 50 2 External UART1 baud rate (RS232)
106 rwf uint EU2BAUD 52 2 External UART2 baud rate
107 r uint16 FWVERHRB 54 1 Interface Board FW version
108 r uint16 CARDID 55 1 0x20: HC121, 0x40: HC122
109 rw int16 MBPARITY 56 1 Parity. 0=none, 1=even, 2=odd
110 rwf int16 MBSTOPBIT 57 1 Stop bits. 1=1 stop bits, 2=2 stop bits
111 rw uint16 MBUSADD 58 1 Modbus Address
112 rwf uint16 MBUSPORT 59 1 Modbus Port. 0=Disable, 1=Enable
113 rwf uint MBUSTO 60 2 Modbus Timeout (ms)
114 r char[20] SYSTIME 62 10 System Time
115
r char[20] SYSDATE 72 10 System Date
117
rw char[20] CONCUNIT 83 10 Concentration Unit of Measure for analyte 1
120
rw char[10] PRESUNIT 95 5 Pressure Unit of Measure, case sensitive.
Valid strings include psi, psia, inH20, inHg,
bar, cmH20, kg/cm2, kPa, mbar, micron,
mmHg, oz/in2, torr, atm
121 rw char[10] TEMPUNIT 100 5 Temp Unit of Measure, case sensistive. Valid
strings include degreeC, degreeF, degreeK
122 r uint DATAVALID 105 2 Data Valid. 0=Not Valid, 1=Valid
123 r int16 DMODE 107 1 0=Line- lock mode, 1=Sample, 2=Calib
125 r uint SYSALARM1 109 2 Bit - mapped system alarms
126 r uint SYSALARM2 111 2 Bit - mapped system alarms
127
r uint USERALARM 113 2 Bit - mapped system alarms
128
r uint CONCALARM 115 2 Bit mapped concentration alarms
Common Modbus Registers
41
129 r int16 SYSSTATUS 117 1 System Status. 0=Everything ok, Not
0=something is wrong
130 r int16 SYSSTATE 118 1 System State. 100=Not Ready, 201=Measure
Run, 502=Idle, 600=diag
133 r float CELLTEMPD 123 2 Cell temp for display
134
r float ANAOUT1 125 2 Current Output 1
135
rw float ANAOUT1O 127 2 Current Output 1 Offset
136
rw uint16 ANAOUT1P 129 1 Current Output 1 Parameter
137 rw float ANAOUT1S 130 2 Current Output 1 Span
138 rw int16 ANAOUT1T 132 1 Current Output 1 Output Type. 0=4- 20 mode,
1=0 - 20 mode.
If overange enable (ANAOUT1OR = 1)
0 = 3.78 - 20.5, 1 = 0 - 20.5, high or low
values can also be set by fault value, See
Fault option (ANAOUT1F)
139 rw uint16 ANAOUT1OR 133 1 Current Output 1 Over range Enable.
0=disabled, 1=enabled
140 rw uint16 ANAOUT1F 134 1 Current Output 1 Fault Option. 0=No fault,
1=Low fault, 2=High fault.
If high fault (2):
High end of range becomes 22 mA
Output ratio becomes 1
If low fault (1) AND in 4- 20 mode
(ANAOUT1T = 0):
Low end of range becomes 3 mA
Output ratio bec omes 0.
141 r float ANAOUT2 135 2 Current Output 2 -
142 rw float ANAOUT2O 137 2 Current Output 2 Offset -
143 rw uint16 ANAOUT2P 139 1 Current Output 2 Parameter-
144 rw float ANAOUT2S 140 2 Current Output 2 Span -
145 rw int16 ANAOUT2T 142 1 Current Output 2 Output Type. 0=4- 20 mode,
1=0 - 20 mode.
If overange enable (ANAOUT2OR = 1)
0 = 3.78 - 20.5, 1 = 0 - 20.5, high or low
values can also be set by fault value, See
Fault option (ANAOUT2F) -
146 rw uint16 ANAOUT2OR 143 1 Current Output 2 Over range Enable.
0=disabled, 1=enabled
147 rw uint16 ANAOUT2F 144 1 Current Output 2 Fault Option. 0=No fault,
1=Low fault, 2=High fault.
If high fault (2):
High end of range becomes 22 mA
Output ratio becomes 1
If low fault (1) AND in 4- 20 mode
(ANAOUT2T = 0):
Low end of range becomes 3 mA
Output ratio becomes 0.
148 r uint16 RELAY1 145 1 Relay 1. 0=OPEN, 1=CLOSED
149 rw uint16 RELAY1D 146 1 Relay 1 Delay. Holds the relay output for this
set amount of time.
150 rw uint16 RELAY1F 147 1 Relay 1 Function. 0=Disabled,
1=Concentration, 3=Data Valid, 4=System
alarm
151
rw uint16 RELAY1S 148 1 Relay 1 Source. The source parameter
number used to evaluated the relay function.
152 rw float RELAY1V 149 2 Relay 1 Value. The value used to evaluate
the relay function.
153 r uint16 RELAY2 151 1 Relay 2. 0=OPEN, 1=CLOSED