manualshive.com logo in svg

AmeriGlide STRATOS VPL, Installation & Service Manual

Share
Download
AmeriGlide STRATOS VPL Installation & Service Manual Download Page 5

STRATOS WITH ENCLOSURE:

 

Install Manual

25MAR2022  |  630-00147 C

5

INTRODUCTION

STRATOS WITH ENCLOSURE: SECTION 2 

SECTION 2

INTRODUCTION

DEVICE NAME:  

STRATOS WITH ENCLOSURE 

PLATFORM LIFT

Indications of Use: The Ameriglide Stratos with 

Enclosure Platform Lift is designed to assist the 

transfer of patients or mobility impaired persons 

and their mobility device, up and down levels of a 

commercial facility or residence. 

READ AND UNDERSTAND

This manual provides instructions for the proper 

installation and service of the Ameriglide Stratos 

with Enclosure Platform Lift which is critical to the 

lift’s safety, performance and durability. Please refer 

to the Owner’s Manual for operating instructions. 

Any alterations to the equipment without written 

authorization by the manufacturer is prohibited and 

will void the warranty.

TECHNICAL SPECIFICATIONS

Visit Ameriglide.com for specifications on the 

particular lift model and configuration.

CODE STATEMENT

The Ameriglide Stratos lift has been designed to 

meet ASME A18.1 “Safety Standard for Platform 

Lifts and Stairway Chairlifts” under section 2 or 

section 5 and has been certified to CAN/CSA-B44.1/

ASME A17.5 “Elevator and Escalator Electrical 

Equipment”.

Code requirements for Vertical Platform lifts may 

vary depending on location. It is the installers 

responsibility to contact their state, city or local 

code enforcement office and determine all the 

regulations the lift and installation are subject 

to. You must do this before installing the Vertical 

Platform Lift.

APPLICABLE STANDARDS 

BASED ON INSTALLATION 

TYPE

Commercial and residential installations require 

compliance to the ASME A18.1 safety code and 

other codes that may be adopted by state, city and 

local code authority having jurisdiction.

To meet the full intent of ASME A18.1 regulation the 

installer is required to contact their state, city or 

local code authority having jurisdiction for permits, 

adopted rules and inspections of the vertical 

platform lift.

Summary of Contents for STRATOS VPL













































Reviews:

No comments

Brands by name

Popular brands

Load more brands