manualshive.com logo in svg

AmeriGlide STRATOS VPL, Installation & Service Manual

Share
Download
AmeriGlide STRATOS VPL Installation & Service Manual Download Page 35

STRATOS WITH ENCLOSURE:

 

Install Manual

25MAR2022  |  630-00147 C

35

TROUBLESHOOTING

STRATOS WITH ENCLOSURE: SECTION 6

Top Lock

Green

LED ON indicates the Top Gate/Door lock is active. 

Pit Switch  

(if equipped)

Green

LED OFF indicates the Pit Switch (if equipped) or Over Speed Governor 

circuit is open. Major Fault. Pit switch and OSG share a circuit that 

normally closed.  Possible causes:  Failure causing drive screw 

overspeed, switch failure, connector open or wire break.  

Safety Pan 

(if equipped)

Green

LED OFF indicates the safety pan circuit is open. Minor Fault. Platform 

is only able to move up. If circuit stays open after obstruction cleared 

there could be a switch failure, connector open or wire break. There are 

11 safety pan switches in platform. 

Bottom Land

Green

LED ON indicates the Bottom Landing switch is closed. The switch 

should be closed only when platform is at that landing.

Float Switch 

(if equipped)

Green

LED ON indicates the float switch (if equipped) is closed. Minor Fault.  

The platform is only able to move up. The switch should be closed only 

when water is present and lifting the float.

Mid Land

Green

If a 3-Stop lift, LED ON indicates the Mid Landing switch is closed. The 

switch should be closed only when platform is at that landing.

Final Limit

Green

LED ON indicates the Top Final Limit switch is closed. Major Fault. The 

Top Landing switch did not close when platform was at that landing.  

Possible causes: Top Landing switch failure, connector open or wire 

break.

Top Land

Green

LED ON indicates the Top Landing switch is closed. The switch should be 

closed only when platform is at that landing.

Summary of Contents for STRATOS VPL













































Reviews:

No comments

Brands by name

Popular brands

Load more brands