manualshive.com logo in svg

AmeriGlide STRATOS VPL, Installation & Service Manual

Share
Download
AmeriGlide STRATOS VPL Installation & Service Manual Download Page 17

STRATOS WITH ENCLOSURE:

 

Install Manual

25MAR2022  |  630-00147 C

17

INSTALLATION

STRATOS WITH ENCLOSURE: SECTION 4

INSTALLING A 90° 

PLATFORM (IF NECESSARY)

If installing a 90° platform, please follow the 

approved drawings for your application. 

The panels are different to accommodate the 

application. See Figure 4-8.  

Figure 4-8

INSTALLING THE PLATFORM 

CONTROL GUARD PANEL

1.  Locate hardware packs for platform in small 

parts bags. 

2.  Insert the control side guard panel posts into the 

pockets on the platform with the smooth side 

facing the inside of the platform. Fasten in place 

with four (4) 1/4

"

- 20 x 2

"

 bolts. Torque bolts down 

sufficiently to hold guard panels rigidly in-place. 

The platform material in front of the pockets may 

deform slightly while tightening bolts. 

3.  Remove the four (4) screws and nuts loosely 

attached to the control box.  

4.  Fasten the control box to the control guard 

panel securely with the four (4) screws and 

nuts. Connect the ground ring terminal to the 

bottom screw connecting the control box to 

the panel. 

INSTALLING THE PLATFORM 

FRONT GUARD PANEL

Insert the front guard panel posts into the pockets 

on the platform with the smooth side facing the 

inside of the platform. Fasten in place with four (4) 

1/4

"

-20 x 2

"

 bolts.

INSTALLING ENCLOSURE 

TOWER WALLS

Your enclosed Stratos will come with a CAD certified 

drawing that was approved by Ameriglide and the 

customer. It will show how the unit should be fixed 

and what hardware should be used. 

1.  Place and shim (if necessary) the lowest front 

wall, the door frame and the tower-side walls 

on the door-side of the enclosure. The lowest 

tower side-panel is vented and is placed with 

the vent side against the back of the tower. 

This side is intentionally left spaced for the 

emergency pit-switch. Assemble and install 

the pit-switch and its housing box.  

See Figure 4-9.

Lowest front 

panel

You may have 

to shim these

Lowest 

outside 

panel 

install pit 

switch

Door frame

Figure 4-9

2.  Install the rest of the front and tower-side 

panels, by stacking them one on top of each 

Summary of Contents for STRATOS VPL













































Reviews:

No comments

Brands by name

Popular brands

Load more brands