manualshive.com logo in svg

AmeriGlide STRATOS VPL, Installation & Service Manual

Share
Download
AmeriGlide STRATOS VPL Installation & Service Manual Download Page 4

STRATOS WITH ENCLOSURE:

 

Install Manual

25MAR2022  |  630-00147 C

4

SAFETY

STRATOS WITH ENCLOSURE: SECTION 1

SECTION 1

SAFETY

SAFETY DEFINITIONS

This safety alert symbol appears with 

safety statements. It means attention, 

become alert, your safety and the 

safety of others are involved! Please 

read and abide by the message that 

follows the safety alert symbol.

NOTE: Indicates a condition that should be followed in 

order for the lift to function in the manner intended.

ENVIRONMENTAL 

CONDITIONS

The technician shall assess the surrounding 

conditions and verify that the location is acceptable 

before performing installation and/or servicing 

tasks. Installation shall not proceed in inclement 

weather conditions that jeopardize the technician’s 

safety or ability to complete the installation in a safe 

manner. Tents, canopies or other outdoor provisions 

that help protect the work area from weather or 

other safety concerns are recommended when 

conditions warrant.

If you do not understand any portion of the 

installation or operation procedures, please consult 

Ameriglide's Support at 866-378-6648. 

Do not attempt to install or use this lift if you have 

any hesitation or question. Serious injury or damage 

can result if proper procedures are not followed.

Indicates a hazardous situation that, if not 
avoided, could result in death or serious injury.

WARNING

!

Indicates a hazardous situation that, if not avoided, 
could result in minor or moderate injury.

CAUTION

!

Indicates a situation which can cause damage to 

the lift and/or the environment, or cause the lift to 

operate improperly.

NOTICE

!

Summary of Contents for STRATOS VPL













































Reviews:

No comments

Brands by name

Popular brands

Load more brands