American Sanders FloorCrafter 8 07104A, Operator'S Manual

Page: 7 / 72

CAUTION: This machine will operate only on AC frequency and on electrical voltage shown on the motor nameplate. Make
sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has
a plug as shown below.
DANGER: Electrocution could occur if the machine is exposed to water or rain. Keep the machine in a dry building.
DANGER: Electrocution could occur if machine is improperly connected to the electrical system. To prevent possible electric
shock, always use a 3 wire electrical system connected to an electrical ground. For maximum protection against
electrical shock, use a circuit that is protected by a ground fault circuit interrupter. Consult your electrical
contractor.
DANGER: Electrocution could occur if the ground pin is tampered with in any way. Do not cut, remove, or break the ground
pin. Do not try to fit a three-terminal plug into a receptacle or connector body other than a three plug receptacle
or connector body. If the outlet does not fit the plug, consult your electrical contractor.
DANGER: Electrocution could occur if the machine is used with a damaged plug or power cord. If the cords or plugs are worn
or damaged in any way, have them replaced by an authorized service person or electrician.
If motor appears to labor or takes a considerable longer time to come up to speed reduce sanding pressure.
Machine Specifications
Introduction
The FloorCrafter can be used on a variety of surfaces. It is an ideal tool for wood flooring maintenance and restoration work. It is
also suitable for cleaning hard surfaces such as tile or Terrazzo.
7
230V Electrical Connection Instructions
This machine must be connected to an electrically ground circuit in order to pro-
tect the operator from electric shock. This machine has an approved power cord
with three conductors as well as a plug with three terminals. Connect the plug into
a three holed receptacle. For maximum protection against electric shock, use a
circuit that is protected by a ground fault circuit interrupter.
Extension Cords
Use only an approved three-pronged extension cord with two main conductors
and one earthing conductor. This machine is equipped
with a power cord. When greater range is needed follow the table
to determine cable gauge of additional footage. Refer to the
chart to the right for extension cord information
EN
Part # 07104A 07104B 07202A 56380917
Model FloorCrafter 8 FloorCrafter 8, Blk FloorCrafter 8 FloorCrafter 8
Electrical Requirements 230~, 60Hz / 15.7 A, 3.7 kW 230~, 60Hz / 15.7 A, 3.7 kW 230~, 60Hz / 15.7 A, 3.7 kW 230~, 50Hz / 16.0 A, 3.0 kW
Sound Emission (Lpm)* 93.0 dB(A) 93.0 dB(A) 93.0 dB(A) 96.2 dB(A)
Vibration <.15 in/s <.15 in/s <.15 in/s 2.88 m/s
2
rms
Motor 4 Hp Induction 4 Hp Induction 4 Hp Induction 3 kW Induction
Contact Wheel Rate 2450 rpm 2450 rpm 2450 rpm 2042 rpm
Abrasive Rate 4500 ft/min 4500 ft/min 4500 ft/min 3750 ft/min
Abrasive Size 29
½
” x 7
⅞
” 29
½
” x 7
⅞
” 29
½
” x 7
⅞
” 29
½
” x 7
⅞
”
Fan Flow Rate 234 CFM 234 CFM 234 CFM 195 CFM
Drum Settings 80 lbs., 70lbs., 60 lbs. 80 lbs., 70lbs., 60 lbs. 80 lbs., 70lbs., 60 lbs. 80 lbs., 70lbs., 60 lbs.
Overload Protection Magnetic Circuit Breaker Magnetic Circuit Breaker Magnetic Circuit Breaker Magnetic Circuit Breaker
Electric Cable 50’, 10-3 SJO LP-20P Plug 50’, 10-3 SJO LP-20P Plug 50’, 10-3 SJO LP-20P Plug 100’, H05VVF3G4.0 AV3-20P Plug
Operating Controls Adjustable Lever/Grip Adjustable Lever/Grip Adjustable Lever/Grip Adjustable Lever/Grip
Leveling Controls Externally Adjustable Externally Adjustable Externally Adjustable Externally Adjustable
Operating Wheels 80 Durometer Clear Urethane 80 Durometer Clear Urethane 80 Durometer Clear Urethane 80 Durometer Clear Urethane
Weight 204 lbs. 204 lbs. 204 lbs. 204 lbs.
Dimensions 35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾
35 x 13
¾
x 38
¾