American Megatrends Megathon User Manual Download Page 28 | Manualshive

Page: 28 / 55

background image

Megathon PCI Motherboard User’s Guide

22

Step 9 Connect I/O,

Continued

J5 Floppy

J5 is a 34-pin dual-inline berg. Connect the cable from the floppy drive to J5, as
shown below. The onboard floppy controller cannot be used if a hard disk card
with a floppy controller is installed. Choose Standard Setup and Peripheral Setup
to configure the floppy controller.

connector with two 34-pin edge connectors for attaching the floppy disk drives.
There is a small twist in the cable between the floppy connectors. The last (end)
connector should be connected to floppy drive A: as shown below.

Cont’d

«
...
26
27
28
29
30
...
»

Summary of Contents for Megathon
























































Reviews:

No comments

Related manuals for Megathon

Brand: Actel Pages: 2

Brand: IBASE Technology Pages: 92

Brand: Telit Wireless Solutions Pages: 5

Brand: Gigabyte Pages: 58

cpuModules CME34BT

Brand: rtd Pages: 110

Brand: Texas Instruments Pages: 24

Brand: BiPOM Electronics Pages: 12

VIOTECH 3100 PLUS - BIOS

Brand: Biostar Pages: 41

Brand: Analog Devices Pages: 6

Brand: Caji Pages: 19

Brand: Gigabyte Pages: 44

Brand: TYAN Pages: 164

Brand: Gigabyte Pages: 38

Brand: Intel Pages: 91

Brand: ASROCK Pages: 5

Brand: DFI Pages: 101

Brand: Asus Pages: 50

Brand: Asus Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands