American Megatrends Megathon User Manual Download Page 42 | Manualshive

Page: 42 / 55

background image

Megathon PCI Motherboard User’s Guide

36

Security Setup,

Continued

Set Supervisor Password

Select Change Supervisor Password from the AMIBIOS Setup main

menu. The password prompt displays.

Type the password and press <Enter>. The screen does not display the
characters entered. Retype the password as prompted and press <Enter>. If the
password confirmation is incorrect, an error message appears. The password is
stored in NVRAM after AMIBIOS completes. The next time the system boots, a
password prompt appears if the Password Check option is set to Always.

Set User Password

Select Change User Password from the AMIBIOS Setup main menu. The

password prompt displays.

Type the password and press <Enter>. The screen does not display the
characters entered. Retype the password as prompted and press <Enter>. If the
password confirmation is incorrect, an error message appears. The password is
stored in NVRAM after AMIBIOS completes. The next time the system boots, a
password prompt appears if the Password Check option is set to

Always.

«
...
40
41
42
43
44
...
»

Summary of Contents for Megathon
























































Reviews:

No comments

Related manuals for Megathon

Brand: ICP Pages: 50

Brand: V2 ELETTRONICA Pages: 12

Brand: Yamaha Pages: 96

Brand: ASROCK Pages: 39

Brand: MATSONIC Pages: 76

Brand: Aaeon Pages: 37

Brand: Ublox Pages: 25

Brand: OpenVox Pages: 29

Brand: EVGA Pages: 2

Brand: IWILL Pages: 54

Brand: Texas Instruments Pages: 44

Brand: MSI Pages: 45

25 Jet FourStroke

Brand: Mercury Pages: 110

Brand: Sleipner Pages: 28

Brand: Texas Instruments Pages: 14

Brand: Texas Instruments Pages: 20

Brand: MSI Pages: 48

Brand: MSI Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands